Bluelab Guardian Monitor (Conductivity / Temperature / pH)

Bluelab Guardian Monitor (Conductivity / Temperature / pH)

SKU: 83708
£259.95
Bluelab Guardian Monitor (Conductivity / Temperature / pH)

Bluelab Guardian Monitor (Conductivity / Temperature / pH)

When growing hydroponically, it's essential to carefully monitor reservoirs to ensure that nutrients of the right strength, temperature and pH are delivered to your plants. The Bluelab Guardian is an all-in-one solution to monitoring every essential parameter. Should levels ever drop below, or rise above, pre-determined values, then the easily programmed visual alarm system kicks into action to alert you to the situation - allowing you to solve minor issues before they become major issues!

  • Bluelab – raising the industry standard
  • Provides consistent, highly accurate readings
  • Unsurpassed build quality
  • Simple alarm system alerts you to drops / increases in read-outs
  • Supplied with a two year guarantee
  • Bold, easily readable LED display
  • Green display doesn't compromise light cycles
  • Water resistant main unit
  • Automatically compensates for temperature differences

Contains:

1 x Bluelab Guardian main unit
1 x conductivity / temperature probe
1 x pH probe
1 x power supply unit
4 x screws (for mounting)
3 x sachets of calibration fluid
2 x cable ties

How the Bluelab Guardian Monitor Works:

Growing hydroponically requires the careful monitoring of a few key nutrient parameters. The values of these parameters can be the difference between a successful grow and a completely failed crop, such is their level of importance.

Growers across the globe regard Bluelab equipment as the best nutrient testing equipment available. The Bluelab Guardian monitors temperature in centigrade or Fahrenheit, conductivity in terms of EC / CF / TDS / ppm, and also pH levels – and it does it consistently and accurately, with the use of scientific grade external probes. The Guardian will even provide a visual alert should levels drop below, or rise above, pre-programmed values – minor issues can then be dealt with before they become major issues.

Many plants flower as a result of changes in the number of hours of uninterrupted darkness they're exposed to. The display LEDs on the Guardian glow in a plant-safe green that won't disturb dark periods and cause unwanted issues.

Differences in the temperature of nutrient solutions can effect pH and EC readings. Because the Bluelab Guardian incorporates a thermometer into its conductivity probe, the data it gathers is used to provide fully temperature compensated pH and EC readings, providing you with the most reliable information possible.

So confident are Bluelab in this product's robustness, that every Guardian comes supplied with a two year guarantee. Only the pH probe is exempt, due to the delicate nature of its glass parts, yet even this still comes with a guarantee of 6 months.

Using the Bluelab Guardian Monitor:

Before doing anything, you should soak the pH probe in KCL (potassium chloride) solution for 24 hours. This is very important!

The Bluelab Guardian can be mounted in a suitable area, using the 4 supplied screws. Make sure that it is placed in an area that will allow the probes to reach the reservoir tank comfortably – no further than two meters away. Two cable ties are supplied with the unit, which can be used to mount it to a support or hanging bar. Avoid positioning the Guardian in areas of direct sunlight. Though the unit is water resistant, you should also avoid positioning it in areas where it can easily be splashed with nutrients. Mineral salt deposits can be corrosive and cause damage over long periods of time.

Choose the correct plug adapter from the supplied selection, connect it to the Guardian's power supply, then connect the power supply to the underside of the main unit. Attach the pH probe to the underside of the unit, by inserting and twisting. The temperature / conductivity probe is supplied pre-attached. The unit can now be powered up at the mains supply.

To select your desired conductivity unit, hold the unit button, located next to the conductivity display, down for 3 seconds. This process will trigger a move to the next unit of measurement, as indicated by the 3 LEDs to the right of the display. Repeat this process until you have arrived at your chosen unit of measurement. Repeat the whole process again for your choice of temperature measurement.

The conductivity / temperature probe is supplied factory calibrated and will only require periodical cleaning. The pH probe, however, will need to be calibrated before use. Add a small amount of pH 7.0 calibration solution to a small beaker or plastic container, dip the end of the probe in the solution and hold the 'pH cal' button, located to the left of the pH read-out display. Rinse the probe tip and repeat the process with either pH 4.0 or pH 10.0 solution to provide a more accurate calibration.

Long-term, the two pH LEDs located to the right of the pH read-out display will keep you informed of the pH calibration status. Consult the full instruction manual for full details on the different statuses. Effectively, if both LEDs are not lit permanently then calibration of some form is required.

The two probes can then be placed in the reservoir tank. Fit the included suction cup holder to the pH probe by gently pushing it over the tip and twisting it round the stem. The probe can now be stuck to the side of the reservoir, preventing it from damage when stirring solutions, etc. The conductivity / temperature probe is less delicate and can be placed straight into the nutrient reservoir.

The alarm function will warn you with a flashing LED when readings drop below, or rise above, a pre-determined value. To set the alarm hold the alarm button until the letters 'AL H' are displayed in each of the three display windows. As soon as you take your finger off the button, the current highest values will be displayed in the three windows. Use the unit buttons to select which parameter you wish to adjust and then use the up and down buttons to lower or increase the each maximum parameter value. Remember that you are setting the highest acceptable value. If levels go above this, then the visual alarm will start to flash. Once you've set the high values, press the alarm button to move onto the low values and repeat the process. Press the alarm button again and your chosen parameters will be saved.

Always take great care with the pH probe. Under no circumstances should you ever allow it to dry out – when not in use, replace the storage cap.

You'll find a copy of the manual for the Guardian Monitor under the attachments tab.