Gavita EL2 Master Controller - Complete Lighting Control System

Ditch your Contactors and Get Access to a Ton of New Features!

The Gavita EL2 Master Controller represents a huge step forward for indoor lighting systems. Now you can replace your contactor / timer set-up by communicating with your ballasts directly via controller cables. The Master Controller system switches up to 80 ballasts from a central point and comes with an easy-to use interface and a clear display. You can even split the 80 ballasts between two rooms in alternating 12/12 cycles. If this wasn't enough, the EL2 comes with a host of features that will increase safety, eliminate inrush current and lower the chances of experiencing botrytis (rot).

How the Gavita Master Controller Works:

The Gavita Master Controller switches up to 80 individual lighting systems from a central point. These 80 lights can be running in the same room or split into two rooms of up to forty lights on a staggered 12/12 cycle. The Gavita Master Controller offers additional features that weren't previously possible with traditional contactor / timer switching systems. It works by sending information to your ballasts directly via controller cables. Compatible ballasts, like the Gavita Digistar 600e, are supplied with RJ14 sockets to create a hard link between the ballast and the EL2 itself. By communicating with ballasts directly, this does away with the need for contactors and timers altogether. Instead, ballasts can be connected to a continuous power supply. This new system opens up the door to a host of new features.

The output levels of up to 80 ballasts can be raised or lowered manually in seconds with the Gavita Master Controller. The EL2 will even adjust light outputs automatically if heat levels in the grow area get too high, thanks to its 'auto-dim' setting. A temperature probe hangs in the canopy area away from direct light and feeds information back to the Master Controller. The Master Controller then uses this information to reduce the output levels of your lighting whenever necessary, ensuring that temperatures never stray above the optimal range (25°C to 28°C). You'll never have to worry about fruits and leaves getting heat-stressed or burnt ever again! And you'll have the peace-of-mind that your grow room is operating safely. The EL2 also has an auto-shutdown feature that shuts off lighting completely when temperatures reach your chosen setting, making it one of the safest options available.

Seasoned growers know that replicating plants' natural conditions as closely as possible is the key to successful indoor gardening. In the outdoors, the transition from light to dark (and vice versa) is very gradual. However, when using a contactor and timer, lighting switches on and off almost instantaneously. The Gavita Master Controller's sunrise/sunset feature takes care of this issue by easing the light levels up and down gently. You can even select the length of time that you'd like the lights to take to do this. The possibility of experiencing botrytis (rot) is then greatly reduced. If lights switch on suddenly, it takes a little while for the temperature of plant matter to reach an equilibrium with the temperature of the air in the room. During this period, the colder outer edges of fruits and leaves make contact with warm air. When warm air hits cold surfaces, condensation forms, and this causes big problems! Moisture sets into delicate areas, triggering botrytis (rot), which can devastate entire crops. By doing things gradually, you'll greatly reduce the chances of this ever happening.

The Gavita EL2 also deals with issues to do with inrush current – a problem that particularly effects growers running multiple lighting systems, as ballasts tend to cause a spike in power when they are first switched on.

The Master Controller comes with RJ9 to RJ14 controller cables that utilize low voltage control currents to interact with ballasts. The RJ9 end plugs into the Gavita Master Controller and the RJ14 end plugs into a compatible ballast, like the Digistar 600e. Digistar E-Series ballasts come supplied with RJ14 to RJ14 cables, so that you can connect the next ballast in the chain to the previous ballast.

The Gavita EL2 Master Controller has two channels - 'main' and 'aux' (both have a separate RJ9 port). The 'main' and 'aux' channels control up to 40 ballasts each. You can use the two channels to control two different rooms if you wish (in which case you will need to use both of the supplied temperature probes – one for each room). This is referred to as 'inverse' mode. Inverse mode is used during the flowering cycle and staggers lighting schedules over twelve hour periods - twelve hours in one room and then twelve hours in the next room. The most common way to use the Master Controller is in 'follow' mode, where the 'main' and 'aux' channels run lights in the same room on the same lighting patterns. In this case, you'll only need to use one temperature probe.

The EL2 can also be connected to two external contactor modules via signal cables, so that you can control additional equipment, like CO2, heaters, plasma lights, etc., based around your lighting patterns. ECM port 1 switches equipment on when are lights are running on the 'main' channel. ECM port 2 switches on equipment while lights are off on the 'main' channel. This functionality allows you to switch equipment on and off inline with your lighting schedules for both the 'follow' and 'inverse' modes. You can use this feature to run other forms of lighting, such as the Gavita LEP range, that don't have a variable output and cannot be adjusted inline with your other ballasts.

To see our full Gavita Pro Lighting range, click here